How to Use Valve Cover Gasket Sealant?
Using the correct valve cover gasket sealant often determines whether a repair will be successful or result in recurring oil leaks.A common mistake many people make is applying too much product, while others apply it to the wrong location.
🔧 Sourcing OEM & Aftermarket Replacement Valve Covers?
IATF 16949 Certified FactoryStop recurring oil leaks caused by warped housings. K-STONE manufactures 100% pressure-decay tested Plastic (PA66+GF30) & Aluminum Valve Covers with pre-installed PCV & gaskets:
The Role of the Valve Cover Gasket Sealant
Modern engines use high-quality rubber or silicone gaskets.These gaskets do 90% of the sealing work.However,engine valve cover gasket sealant is necessary for specific “problem areas.”
The sealant fills microscopic gaps that the rubber gasket cannot bridge.It is flexible and heat-resistant.It handles the expansion of the metal engine parts.However,it is not a glue.Its primary job is to assist the main gasket,not replace it.
Get A Quote Now
Where to Apply Valve Cover Gasket Sealant
Applying the sealant to the correct location is critical.Typically,valve cover gasket sealant should not be applied across the entire gasket surface,as this may cause the gasket to shift.
Special attention should be paid to transition areas.The most common leakage points occur where two different surfaces meet.
- The Half-Moons:
Apply sealant where the semi-circular camshaft plugs meet the flat cylinder head. - Sharp Corners:
Apply a small dab in the corners of the front timing cover. - Surface Splits:
Any area where the engine block meets a separate casting needs a drop.
| Location on Cylinder Head | Apply Sealant? | Reason |
|---|---|---|
| Flat Mating Surface | NO | The rubber gasket seals this best alone. |
| Sharp Corners (90°) | YES | Rubber gaskets compress poorly in sharp corners. |
| Half-Moon Cutouts | YES | These areas have gaps between the plug and the head. |
| Spark Plug Wells | NO | The gasket rings here are designed to seal dry. |
Choosing the Right Product
Look for “RTV” (Room Temperature Vulcanizing) silicone.It must be “Sensor Safe.”If it is not sensor safe,the fumes can destroy your Oxygen (O2) sensors.Usually,Grey or Black RTV is best for high-torque applications. Blue RTV is generally for water pumps, not oil.
Step-by-Step Application Guide
Surface Preparation
The metal surface must be perfectly clean.Use brake cleaner and a lint-free rag.Remove all old oil and residue.If the surface is oily,the valve cover gasket sealant will not stick.It will eventually blow out.
Apply the Sealant
Squeeze a small amount of gasket sealant onto the specific target areas. Do not use too much.A bead the size of a small pea is usually enough.
Warning:
Excess sealant is dangerous.If it squeezes inside the engine,it can break off.These cured chunks can fall into the oil pan.Eventually,they clog the oil pickup screen.This starves the engine of oil and causes catastrophic failure.
Install the Gasket and Cover
Place the gasket onto the valve cover first.Then,lower the cover onto the cylinder head.Be careful not to smear the wet valve cover gasket sealant.
Finger Tighten Only
Install the bolts and tighten them only until they touch the cover.Do not torque them yet.Let the sealant sit for about 30 to 60 minutes.This allows the product to “skin over.”
Final Torque
After the waiting period,tighten the bolts to the manufacturer’s specified torque.This operation will compress the sealant to form a permanent seal.
Curing Times and Best Practices
| Phase | Time Required | Action |
|---|---|---|
| Skin Time | 15 – 30 Minutes | Wait before final torque. |
| Functional Cure | 2 – 4 Hours | Safe to add oil, but do not start engine. |
| Full Cure | 24 Hours | Safe to drive and expose to high heat. |
Common Mistakes to Avoid
- Over-application:
Using a thick bead around the whole cover.This guarantees a messy leak. - Wrong Chemistry:
Using household bathroom silicone.The acetic acid in it eats aluminum. - Rushing:
Starting the car immediately after installation. - Dirty Surfaces:
Applying valve cover gasket sealant over old grease.
Contact Us Now
- RM901 No.22 Tangjiaqiao Road Wenzhou China
- +86 138 1973 9327
- [email protected]
- https://www.autosparesupplier.com/

